Images tagged "amiga"

  • Pingback: Sheevaplug as a perfect NAS

  • Pingback: HTTP driven power switches and UART to telnet gateway with an Arduino

  • Pingback: Deploying Saltstack : master and minion (archlinux on ARM)

  • Pingback: Homemade streetfighter themed bartop with light gun

  • Steve
    February 1, 2017 at 13:34

    Great post and your boot time is quite impressive also. With raspbian I get well over 1 minute. I might redo mine with archlinux 🙂

    Reply
    • jit
      February 6, 2017 at 18:15

      Thank-you. The ArchLinux base install is very lightweight, so its clearly a better bet for starting optimization ! Nevertheless, an even faster boot should be easily reachable with a buildroot based solution 😉

      Reply

  • Pingback: Deploying Saltstack : master and minion (archlinux on ARM)

  • Pingback: GamOdroiD C0 : an Odroid based portable retrogaming

  • chapichapo
    October 30, 2017 at 00:12

    Hello, is this still useable? I’d like to use my Zibase instead of getting a Z-wave module for my openhab install… but since the addon was not updated recently, I’d like to know if it still works with openhab2? And where I can find the instructions to install it?

    Thanks,

    Reply
    • jit
      November 7, 2017 at 23:43

      Hello, I still used it until few weeks ago (but with openhab 1.8). To be honest, I just build a Rflink based solution with MQTT (article to come in a few days) and it works muh better than the Zibase,so I probably won’t do any update. Moreover, I never been able to test Zwave as I don’t have such device at home.

      However, it works like any other OpenHab Binding, the documentation is in the official wiki : https://github.com/openhab/openhab1-addons/wiki/Zibase-Binding

      Reply

  • Pingback: Another NAS with a BananaPI | bluemind.org

  • Pingback: Another NAS with a BananaPI | bluemind.org

  • Pingback: Mqtt / json Arduino shield for Rflink

  • Pingback: Existing RetroGaming handled console – My RetroGaming journey

  • Pingback: Odroid N1 as a NAS in a home made 19 inches rack mount

  • Pingback: Odroid N1 as a NAS in a home made 19 inches rack mount

  • Pingback: Odroid HC1 based swarm cluster in a 19″ rack | bluemind.org

  • EmilioRLL
    February 21, 2019 at 12:55

    Emula ps2?

    Reply

  • Pingback: Arduino driven 5v and 12v Smartpower – maker.wiznet.io

  • Pingback: Odroid HC1 based swarm cluster in a 19″ rack

  • Daniel Quah
    December 8, 2019 at 10:43

    Hi!

    Thanks for your post!

    Would you by any chance be making these replacement battery packs for sale? I face a similar problem but I am a klutz when it comes to electronics stuff.

    Thanks again!

    Reply
  • Cengiz Gören
    February 15, 2020 at 08:18

    Hi there , i really like this version .. and this i s what i want to build. Do you maybe have a good schematic ? because im a beginner. i dont know your photos.. looks great but i cant figure out the pins.. DO YOU HAVE A FRITZING? OR SIMILAR OR CAN YOU MAKE IT THE SCHEMATICS ? but like you have it .with 5 way schematic and mosi display..

    Reply

  • Pingback: Odroid C1 optimized retroarch

  • John Austen Clayton
    April 18, 2020 at 10:57

    Great work. I’m in the process of doing something similar with my X-Craft (which is definitely the most powerful and fastest ready to run RC hovercraft in my experience).
    Was the hovercraft more or less powerful with the Li-Po battery?

    Is there anyone out there who can help me out with photos of each page of an X-Craft’s manual/user guide, please?

    Reply
  • John
    May 6, 2020 at 22:03

    I did the same battery upgrade. It gives much more run time, but the Hovercraft is also significantly faster e.g. it will now get ‘on plane’ on water. Very pleasing!

    Did your X-craft go any faster with the new battery?

    Reply
    • jit
      May 20, 2020 at 15:37

      I did not see any change regarding motors’ power. Voltage with lipo are close to NiMH original battery I guess.
      And… Hmmm I’m sorry but I do not have the manual anymore.

      Unfortunately, the skirt has a hole now, and I can’t find somewhere to buy another one ;(

      Reply
  • John Clayton
    December 27, 2020 at 12:44

    You could repair the hole with a bicycle puncture repair kit

    Reply
  • Jonathr67
    April 21, 2021 at 17:56

    Hi, how do you play cd with volumio ? With a premium account ? Or with Nanosound CD plugin. I use the second one but i have many bugs, sometimes it doesn’t work, i didn’t have any sound and cd ripping doesn’t work at all.

    Second question, i want to use your plugin gpiorandom. I have an click switch with two pin and it need to be connected to gpio pin who support interruption… pin 3 is ok ?
    One on pin 3 an the other on grnd ?

    Thank you for your help

    Reply
    • jit
      May 5, 2021 at 12:18

      Hi, I use a premium account for CD playing… it is more to support volumio dev than anything else.

      Yes, Pin 3 is ok for interrupt. one wire on pin 3 and the other on GND (pin 4, for exemple)

      Reply
  • Jonr67
    April 25, 2021 at 12:33

    Hi, thank you for your volumio plugin, gpiorandom is very awesome ! just one request, it will be nice if your plugin can control two buttons. Two button with three action will be nice !

    And you think adding the fonction play a random playlist on spotify is possible ?

    Thank you again +1

    Reply
    • jit
      May 5, 2021 at 12:15

      Hi, that’s a good idea to add another button. I’m not going to implement it very soon because I’m finishing a customm volumio build for my Odrophile tablet. But I keep your proposal in mind 😉

      Reply

  • Pingback: Odrophile update : am odroid based DIY audiophile tablet

  • Pingback: GamOdroid C0 : my odroid C0 based handheld console has been updated !

  • Robert June Tria
    November 4, 2021 at 18:13

    Hi! Thanks for sharing this! My Arduboy parts have been gathering dust all this time due to me loosing interest because SSD1306 Oled is too tiny. But Mr.Blinky (big thanks Mr.Blinky) made the SH1106 work for the Arduboy… now I got my SH1106 Arduboy… Thank you!

    Reply
  • Rosario
    February 16, 2022 at 19:43

    Hello, I came across this blog during a Google search about Pi DAC Volumio and CD player.
    What about Power ?
    I mean you are running a Pi / DAC and an USB CD player. Which Power adapter do you use? Does a simple Pi Power adapter (5v/2a) support the whole system?
    Thank you!

    Reply
    • jit
      April 27, 2022 at 09:32

      I use only one power supply which is the one that comes with the PecanPi streamer : 9v 2.5A. The pi is powered by the PecanPi Board and the USB CD Player is powered directly from the USB port of the Pi

      Reply
  • Leo A.
    April 20, 2022 at 14:33

    Hi,

    This is a great project. Thanks for sharing.

    Regards
    Leo

    Reply

  • Pingback: Rflink with mqtt V2 : enhanced and minimized | bluemind.org

  • Whites
    January 5, 2023 at 04:29

    1 year+ after this post, are you still happy with the product?

    Reply
  • AJ
    April 16, 2023 at 09:48

    Great project! I gathered all the required parts and printed the enclosure: THANKS for sharing!.

    Looking at the pictures, the text and the instructions in the rflink documentation I think there is one thing in the wiring discription that is not correct. The VCC of the STX and SRX should not be connected since the STX should be powered using D15 as stated in the RFLink documentation. This also seems to be what you have done in the last picture, but in the text and other pictures it still looks like the VCC’s of the STX and SRX should be connected.

    In addition I have a problem with compiling the RflinkToJsonMqtt sketch. My Common.h looks like (only defined the MQTT_SERVER_IP):
    +++++++++
    // MQTT Server IP
    #define MQTT_SERVER_IP (192, 168, 178, 2)
    // MQTT Server name
    //#define MQTT_SERVER_NAME “mqtt.local.lan”
    // MQTT Server mode : comment out to use MQTT_SERVER_IP instead of MQTT_SERVER_NAME
    //#define MQTT_SERVER_MODE_DNS
    +++++++++

    But when compiling I get an error that there are multiple definitions of ‘SERVER’ …. See the output below:

    ++++++++++
    Arduino: 1.8.19 (Windows Store 1.8.57.0) (Windows 10), Board: “LOLIN(WEMOS) D1 R2 & mini, 80 MHz, Flash, Legacy (new can return nullptr), All SSL ciphers (most compatible), 4MB (FS:2MB OTA:~1019KB), v2 Lower Memory, Disabled, None, Only Sketch, 921600”

    Multiple libraries were found for “PubSubClient.h”
    Used: C:\Users\arman\OneDrive\Documenten\Arduino\libraries\PubSubClient
    Not used: C:\Users\arman\OneDrive\Documenten\Arduino\libraries\ESP8266_Microgear

    c:/users/arman/onedrive/documenten/arduinodata/packages/esp8266/tools/xtensa-lx106-elf-gcc/2.5.0-4-b40a506/bin/../lib/gcc/xtensa-lx106-elf/4.8.2/../../../../xtensa-lx106-elf/bin/ld.exe: sketch\RflinkToJsonMqtt.ino.cpp.o:C:\Users\arman\OneDrive\Documenten\Arduino\RFLinkMQTT\RflinkToJsonMqtt/Mqtt.h:15: multiple definition of `SERVER’; sketch\Mqtt.cpp.o:C:\Users\arman\OneDrive\Documenten\Arduino\RFLinkMQTT\RflinkToJsonMqtt/Mqtt.h:15: first defined here

    collect2.exe: error: ld returned 1 exit status
    exit status 1
    Error compiling for board LOLIN(WEMOS) D1 R2 & mini.
    ++++++++++++++++

    Any ideas what could be wrong? Thanks for the help.

    Reply
    • jit
      April 30, 2023 at 22:04

      You’re right, there was a mistake in my wiring table : the STX is powered by the Arduino D15 pin. I corrected the article.
      Regarding the compilation, I still need to try again on my side with fixed IP option.

      Reply